>
Home > CAVITATION
Sort By:
Page of 2
1" Marine Hose
1" Marine Hose
Our Price: $2.00

Heavy duty marine thick wall prop shaft log hose. 1" inside diameter. Will fit our 1" cav rod seals. Also check out our 1" Stainless T-Bolt Clamps.

Price $2.00 per inch (EX. 1" = 1Qty) (EX. 2" = 2Qty ) (EX. 3" = 3Qty) etc.

1 1/4". Marine Hose
1 1/4". Marine Hose
Our Price: $2.00

Heavy duty marine thick wall prop shaft log hose. 1 1/4" inside diameter. Will fit our 1 1/4" cav rod seals. Also check out our 1 1/4" Stainless T-Bolt Clamps.

Price $2.00 per inch (EX. 1" = 1Qty) (EX. 2" = 2Qty ) (EX. 3" = 3Qty) etc.



1" T-Bolt Clamp
1" T-Bolt Clamp
Our Price: $7.00

100% stainless steel construction. 1/4"-20 bolt with nylock nut. 3/4" wide. Will fit our 1" cav rod seal hose. Also check out our 1" cav rod rubber hose.

1 1/4" T-Bolt Clamp
1 1/4" T-Bolt Clamp
Our Price: $7.00

100% stainless steel construction. 1/4"-20 bolt with nylock nut. 3/4" wide. Will fit our 1 1/4" cav rod seal hose. Also check out our 1 1/4" cav rod rubber hose.


Turnbuckle Bolts
Turnbuckle Bolts
Our Price: $10.25



Custom made stainless steel turnbuckle bolts. Eliminate
loosing E-clips forever. Direct replacement. Standard 3/8" diameter pin
with a 1/4" thread that meets in the middle for zero chance of shearing.
1/2" hex that has both sides clocked for a uniform appearance. Fits
standard .700 wide turnbuckles.

Cav Rod Seal Rebuild Kit.
Cav Rod Seal Rebuild Kit.
Our Price: $12.95

1x o-ring and 2x double lip grease cup seals.
TURNBUCKLE 7 3/8"
TURNBUCKLE 7 3/8"
Our Price: $32.00



Made from 6061-T6 aluminum that can be polished or anodized
to match your existing hardware. Fits standard 5/16” wide standoffs and pads.
Also fits standard 3/8” diameter turnbuckle bolts, also available on our
website. Hide-A-Nut design to cover up the turnbuckle threads in any position.
Beefy 5/8” diameter stud that has been gun drilled thru for strength and
weight. Flats are also located on the stud for adjustment. Locknuts fit a
standard ¾” wrench.



The 7 3/8” size fits a range from 6 7/8” to 7 7/8”.

TURNBUCKLE 8"
TURNBUCKLE 8"
Our Price: $32.00



Made from 6061-T6 aluminum that can be polished or anodized
to match your existing hardware. Fits standard 5/16” wide standoffs and pads.
Also fits standard 3/8” diameter turnbuckle bolts, also available on our
website. Hide-A-Nut design to cover up the turnbuckle threads in any position.
Beefy 5/8” diameter stud that has been gun drilled thru for strength and
weight. Flats are also located on the stud for adjustment. Locknuts fit a
standard ¾” wrench.



The 8” size fits a range from 7 ½”” to 8 ½””.

TURNBUCKLE 8 3/4"
TURNBUCKLE 8 3/4"
Our Price: $32.00



Made from 6061-T6 aluminum that can be polished or anodized
to match your existing hardware. Fits standard 5/16” wide standoffs and pads.
Also fits standard 3/8” diameter turnbuckle bolts, also available on our
website. Hide-A-Nut design to cover up the turnbuckle threads in any position.
Beefy 5/8” diameter stud that has been gun drilled thru for strength and
weight. Flats are also located on the stud for adjustment. Locknuts fit a
standard ¾” wrench.



The 8” size fits a range from 8 1/4”” to 9 1/4””.

1" Cavitation Rod Seal
1" Cavitation Rod Seal
Our Price: $44.00

New design Cavitation Rod Seal (to match my bearing prop shaft log seals).
The 1 size refers to the inside diameter of the rubber hose that is attached to you thru hull fitting.
They are made to fit 1/2" diameter cavitation rods. Made from 6061-T6 Aluminum. They have 2 double lip cup seals with a gap in between them for grease. A snap ring on the front for containment and safety. Also at the water side is an o-ring for a total of 3 water seals.
Also, while replacing your Cav Rod Seal, please check out our 1" Marine Grade Rubber Hose and 100% Stainless Steel T-Bolt Clamps.
   
 

Copyright ©  . All Rights Reserved.

Built with Volusion.