>
Home > RUNNING GEAR
Sort By:
Page of 2
1 3/4" Marine Hose
1 3/4" Marine Hose
Our Price: $2.00

Heavy duty marine thick wall prop shaft log hose. 1 3/4" inside diameter and 2 1/4" outside diameter. Will fit our 1" and 1 1/8" prop shaft seals. Also check out our 1 3/4" Stainless T-Bolt Clamps.

Price $2.00 per inch (EX. 1" = 1Qty) (EX. 2" = 2Qty ) (EX. 3" = 3Qty) etc.
1 3/4" T-Bolt Clamp
1 3/4" T-Bolt Clamp
Our Price: $7.00

100% stainless steel construction. ¼”-20 bolt with nylock nut. 2.340 maximum opening and 2.030 minimum closing. ¾” wide. Will fit our 1” and 1 1/8” prop shaft seals. Also check out our 1 ¾” shaft log rubber hose.



1.00 X 1.25 STRUT BEARING
1.00 X 1.25 STRUT BEARING
Our Price: $18.00

Aqua Lube Water Lubricated Marine Strut Bearing.
Cut in half and install each piece into strut

I.D.: 1"

O.D.: 1 1/4"

Length: 4"

1.00 X 1.375 STRUT BEARING
1.00 X 1.375 STRUT BEARING
Our Price: $22.00

Aqua Lube Water Lubricated Marine Strut Bearing.
Cut in half and install each piece into strut

I.D.: 1"

O.D.: 1 3/8"

Length: 4"

1.125 X 1.375 STRUT BEARING
1.125 X 1.375 STRUT BEARING
Our Price: $22.50

Aqua Lube Water Lubricated Marine Strut Bearing.
Cut in half and install each piece into strut

I.D.: 1 1/8"

O.D.: 1 3/8"
Length: 4"

1" Prop Seal Rebuild Kit
1" Prop Seal Rebuild Kit
Our Price: $22.95

1x precision bored, sealed bearing and 2x double lip grease cup seals.


1 1/8" Prop Seal Rebuild Kit
1 1/8" Prop Seal Rebuild Kit
Our Price: $22.95

1x precision bored, sealed bearing and 2x double lip grease cup seals.



1" Aluminum Split Safety Collar
1" Aluminum Split Safety Collar
Our Price: $33.95

Fits 1" prop shafts or 1" rudders. New smooth / lightweight design. Made from 6061-T6 aluminum with a nice machined finish. Can be easily polished or anodized. 2 3/8" outside diameter and 11/16" wide. Both 5/16" tapped holes do not break through as to not expose the threads for a clean look. Supplied w 2x 5/16"-24 stainless steel socket head cap screws.
1 1/8" Aluminum Split Safety Collar
1 1/8" Aluminum Split Safety Collar
Our Price: $33.95

Fits 1 1/8" prop shafts or 1 1/8" rudders. New smooth / lightweight design. Made from 6061-T6 aluminum with a nice machined finish. Can be easily polished or anodized. 2 3/8" outside diameter and 11/16" wide. Both 5/16" tapped holes do not break through as to not expose the threads for a clean look. Supplied w 2x 5/16"-24 stainless steel socket head cap screws.
1" Prop Shaft Seal
1" Prop Shaft Seal
Our Price: $89.00

Made from 6061-T6 aluminum with a machined finish. They are approximately 2 1/2" diameter by 2 1/2" long. There is a lightly pressed in 2" diameter double sealed bearing with the inside diameter bored to 1.003" (to easily slip over your prop shaft). It held in the aluminum housing by a snap ring for safety.
Inside the aluminum housing is two double lip cup seals to keep the water out and a grease zert on the outside body to grease the seal. A standard size 1 3/4" hose fits from the rear, I also added rounded grooves to help the hose clamp bite into the housing and not slip off.
With this design there will be no more prop shaft wear of bushings to replace because it rides on a bearing.
Also, while replacing your prop shaft seal, please check out our 1 3/4" Marine Grade Rubber Hose and 1 3/4" 100% Stainless Steel T-Bolt Clamps.

Please read "Installation and Maintenance" section.





   
 

Copyright ©  . All Rights Reserved.

Built with Volusion.